p10

[cooldude]

i need some advice on p10 usage

from someone who spent some time playin with this great product.
I ve used anywhere from 0.5 ml to 1.5 ml of pure

p10 per application. Normally i dont use the ethanol that comes with it.
i cant seem to figure out what the right

amount is. is 0.5 too low..is 1.5 too high..overall teh product is actually perfect..well deserved name

[oscar]

i need some advice

on p10 usage from someone who spent some time playin with this great product.
I ve used anywhere from 0.5 ml to

1.5 ml of pure p10 per application. Normally i dont use the ethanol that comes with it.
i cant seem to figure out

what the right amount is. is 0.5 too low..is 1.5 too high..overall teh product is actually perfect..well deserved

name

cooldude,

One drop of P10 is a pretty hefty dose. It has a higher Androstenone

content than Primal Instinct. (.6mg/mL vs .5mg/mL)

Do yourself a favor and mix one mL of P10 with 3mL of the

ethanol, and try using one or two drops at 25% strength.

When you used 1.5mL at once you wasted roughly 45

full .02mg doses of Androstenone.

You're really not going to get your money's worth that way.



Oscar

[cooldude]

i agree using 1.5 ml at once is

a waste since the whole thing is like 10 ml. When i mix 1 ml of p10 with 3ml of ethanol,
(now i have p10 at 25%

strenghth)..at this point should i spray the whole 4ml(phero+ethanol) mix at once. Or should that be
used for more

than one application, if so how many?
i get a little confused when the ethanol is introduced...id rather not use

it to dilute the phero..instead i can jsut use
a lower ammount of p10 per application. as far as i know its only

for dilution purposes..
if you can tell me how many mls of p10 to use per application i am the hhappiest man!!!

with 0.5 ml per applicaton the whole
thing lasts for over 20 applciations which is not too bad..unless the 0.5 ml

of p10 at once is an OD.

[oscar]

i agree using 1.5 ml

at once is a waste since the whole thing is like 10 ml. When i mix 1 ml of p10 with 3ml of ethanol,
(now i have

p10 at 25% strenghth)..at this point should i spray the whole 4ml(phero+ethanol) mix at once. Or should that

be
used for more than one application, if so how many?
i get a little confused when the ethanol is

introduced...id rather not use it to dilute the phero..instead i can jsut use
a lower ammount of p10 per

application. as far as i know its only for dilution purposes..
if you can tell me how many mls of p10 to use per

application i am the hhappiest man!!! with 0.5 ml per applicaton the whole
thing lasts for over 20 applciations

which is not too bad..unless the 0.5 ml of p10 at once is an OD.

cooldude,

Maybe there's a

language barrier at work here. I'll try to simplify what I already posted.

ONE DROP is a BIG DOSE of P10.

That means that .5 mL is about 10 or 15 big doses.

You should use the ethanol to dilute the P10 concentrate

because:

a.) You may find that less than one full drop of the concentrated product is your optimal dose (and

it's difficult, if not impossible, to get droppers to dispense partial drops.)

b.) A less concentrated

version of the product will enable you to spread out your single dose over several application

points.


Start out with one drop of the diluted version. Then try two,..three,.. etc.
Over four drops

(of the 25% dilution) will probably be an OD.

DON'T THINK that using a lot will get you more/better

results. It doesn't work that way.

The 10mL bottle of

Perfect Ten SHOULD last you well over 200

applications.

Oscar