View Full Version : p10
cooldude
12-11-2006, 12:47 PM
i need some advice on p10 usage
from someone who spent some time playin with this great product.
I ve used anywhere from 0.5 ml to 1.5 ml of pure
p10 per application. Normally i dont use the ethanol that comes with it.
i cant seem to figure out what the right
amount is. is 0.5 too low..is 1.5 too high..overall teh product is actually perfect..well deserved name :lovestruc
oscar
12-11-2006, 03:52 PM
i need some advice
on p10 usage from someone who spent some time playin with this great product.
I ve used anywhere from 0.5 ml to
1.5 ml of pure p10 per application. Normally i dont use the ethanol that comes with it.
i cant seem to figure out
what the right amount is. is 0.5 too low..is 1.5 too high..overall teh product is actually perfect..well deserved
name :lovestruc
cooldude,
One drop of P10 is a pretty hefty dose. It has a higher Androstenone
content than Primal Instinct. (.6mg/mL vs .5mg/mL)
Do yourself a favor and mix one mL of P10 with 3mL of the
ethanol, and try using one or two drops at 25% strength.
When you used 1.5mL at once you wasted roughly 45
full .02mg doses of Androstenone.
You're really not going to get your money's worth that way.
;)
Oscar :)
cooldude
12-11-2006, 06:38 PM
i agree using 1.5 ml at once is
a waste since the whole thing is like 10 ml. When i mix 1 ml of p10 with 3ml of ethanol,
(now i have p10 at 25%
strenghth)..at this point should i spray the whole 4ml(phero+ethanol) mix at once. Or should that be
used for more
than one application, if so how many?
i get a little confused when the ethanol is introduced...id rather not use
it to dilute the phero..instead i can jsut use
a lower ammount of p10 per application. as far as i know its only
for dilution purposes..
if you can tell me how many mls of p10 to use per application i am the hhappiest man!!!
with 0.5 ml per applicaton the whole
thing lasts for over 20 applciations which is not too bad..unless the 0.5 ml
of p10 at once is an OD.
oscar
12-16-2006, 08:39 AM
i agree using 1.5 ml
at once is a waste since the whole thing is like 10 ml. When i mix 1 ml of p10 with 3ml of ethanol,
(now i have
p10 at 25% strenghth)..at this point should i spray the whole 4ml(phero+ethanol) mix at once. Or should that
be
used for more than one application, if so how many?
i get a little confused when the ethanol is
introduced...id rather not use it to dilute the phero..instead i can jsut use
a lower ammount of p10 per
application. as far as i know its only for dilution purposes..
if you can tell me how many mls of p10 to use per
application i am the hhappiest man!!! with 0.5 ml per applicaton the whole
thing lasts for over 20 applciations
which is not too bad..unless the 0.5 ml of p10 at once is an OD.
cooldude,
Maybe there's a
language barrier at work here. I'll try to simplify what I already posted.
ONE DROP is a BIG DOSE of P10.
That means that .5 mL is about 10 or 15 big doses.
You should use the ethanol to dilute the P10 concentrate
because:
a.) You may find that less than one full drop of the concentrated product is your optimal dose (and
it's difficult, if not impossible, to get droppers to dispense partial drops.)
b.) A less concentrated
version of the product will enable you to spread out your single dose over several application
points.
Start out with one drop of the diluted version. Then try two,..three,.. etc.
Over four drops
(of the 25% dilution) will probably be an OD.
DON'T THINK that using a lot will get you more/better
results. It doesn't work that way.
The 10mL bottle of
Perfect Ten (http://love-scent.com/product_info.php?ref=66&products_id=28) SHOULD last you well over 200
applications.
Oscar :)
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.